MCM 2019
14th Multinational Congress on Microscopy

September 15-20, 2019 in Belgrade, Serbia

Days
Hours
Minutes
Seconds

Oil Immersion Microscopy: How to Use the 100x Objective Step by Step

· 8 min read

Oil immersion microscopy places a drop of oil between the cover glass and a 100x objective so light reaches the lens without bending away at an air gap. The result is a higher numerical aperture and sharper detail at 1000x. Here is how it works, the exact routine to follow and the mistakes that damage lenses.

What oil immersion microscopy actually does

Oil immersion microscopy replaces the thin layer of air between the cover glass and the front lens of the objective with a drop of oil whose refractive index is almost identical to glass. Immersion oil for light microscopy is formulated to about 1.515, while standard cover glass sits close to 1.52. Light leaving the specimen therefore travels through what is optically one continuous medium instead of bending sharply at a glass-to-air boundary.

That matters because air (refractive index 1.0) refracts and reflects the most oblique rays away from the objective. Those steep rays carry the finest detail in the image. When the gap is filled with oil, they reach the front lens, the objective can work at a much higher numerical aperture (NA), and resolution improves. If you want the full optical background first, the article on how a light microscope works covers Köhler illumination and the resolution limit in more depth.

Numerical aperture and resolution in one paragraph

Numerical aperture is NA = n × sin θ, where n is the refractive index of the medium in front of the lens and θ is the half-angle of the light cone the lens accepts. A dry objective can never exceed NA 1.0 in theory and reaches roughly 0.95 in practice. A typical 100x oil immersion objective is rated NA 1.25 to 1.4. Using the familiar estimate d = 0.61 λ / NA with green light (about 550 nm), NA 0.95 gives roughly 0.35 µm, while NA 1.4 gives about 0.24 µm. That gain is the whole reason the technique exists.

Oil immersion microscope lens: how to recognise it

The question "oil immersion microscopy uses which objective lens" has a short answer: almost always the 100x objective, sometimes also 60x or 63x oil objectives on research stands. The barrel tells you what you have.

  • Engraving: look for "Oil", "Oel", "HI" (homogeneous immersion) or "Imm" next to the magnification.
  • Colour ring: a black ring near the front lens conventionally marks oil immersion. Water objectives usually carry a white ring.
  • NA above 1.0: any objective rated NA 1.25 or 1.4 must be used with oil; it cannot form a sharp image in air.
  • Spring-loaded tip: most 100x objectives have a retractable front section that protects the slide and lens if you focus too far.
  • Cover glass value: "0.17" means it is corrected for a No. 1.5 cover glass, roughly 0.17 mm thick.
ObjectiveTypical NAMediumWorking distanceTotal magnification with 10x eyepiece
10x dry0.25AirSeveral mm100x
40x dry0.65AirUnder 1 mm400x
60x/63x oil1.4OilAround 0.1–0.2 mm600x/630x
100x oil1.25–1.4OilAround 0.1–0.2 mm1000x

The 1000x figure is the oil immersion microscope magnification most students meet in class. The calculation is simply objective times eyepiece; what changes with oil is not the multiplication but the amount of real detail that survives at that magnification.

Oil immersion microscopy technique, step by step

The routine below works on any upright compound microscope. The key idea is that you never search for the specimen with the 100x objective. You find and centre it at low power, then move up.

  1. Prepare the slide properly. Use a fixed, dry smear or a mounted specimen under a cover glass. Wet mounts tend to float and smear oil into the sample.
  2. Set up the light at low power. Focus with the 10x objective, adjust the condenser height and field diaphragm, and open the condenser aperture to suit the objective.
  3. Centre the area of interest. Move to 40x, focus with the fine knob and place the exact structure you want in the middle of the field.
  4. Swing the turret halfway. Rotate the nosepiece so that no objective is over the slide. This leaves room to apply oil without touching any lens.
  5. Apply one small drop. Put a single drop of immersion oil on the cover glass directly over the illuminated spot. Avoid shaking the bottle, which creates bubbles.
  6. Click the 100x objective into place. Its tip should dip into the oil. Look from the side, not through the eyepieces, while it settles.
  7. Focus with the fine knob only. A parfocal microscope will be close to focus already. Small adjustments of a fraction of a turn are enough.
  8. Optimise the condenser. For the best resolution with an NA 1.25–1.4 objective, open the condenser aperture to about 70–80 percent of the objective's aperture. Some setups also oil the condenser top lens for maximum NA.
  9. Do not go back to 40x through the oil. If you need lower power again, clean the slide first, or switch straight to 10x, which has enough working distance to stay dry.

Key takeaway: find the target at 40x, rotate the turret to an empty position, add one drop of oil, and bring in the 100x objective. The dry 40x lens must never swing back through the oil.

Choosing immersion oil: types and what they mean

Not every oil is interchangeable. Manufacturers formulate oils to match their own lens designs, and mixing brands or types can change the refractive index or create a cloudy emulsion. The common labels refer mainly to viscosity and fluorescence.

Oil typeViscosityBest forNote
Type ALow (around 150 cSt)Routine work, quick changes between slidesSpreads easily, fewer bubbles
Type BHigh (around 1250 cSt)Longer observations, bridging a larger gapStays put but traps air more easily
Low-fluorescence oils (often labelled F or FF)Low to mediumFluorescence imagingMinimal background glow under UV and blue excitation
Very high viscosity oilsVery highInverted and inclined microscopesWill not run off a vertical or upside-down lens

For fluorescence, a low-fluorescence oil is not optional. Standard oils can glow faintly under short-wavelength excitation and lower the contrast of dim signals. The refractive index of oil also changes slightly with temperature, so some live-cell users choose oils specified for 37 °C.

Common mistakes with the 100x oil objective

Oil on a dry objective

The most frequent and most expensive error is rotating the 40x objective back over an oiled slide. Its front lens sits very close to the cover glass and picks up oil immediately. Dry objectives are not sealed for oil, and residue that is not removed can creep into the lens mount. If it happens, clean the front lens at once with lens paper and an appropriate cleaner.

Air bubbles in the drop

Bubbles scatter light and make the image look hazy or low in contrast. Check by removing an eyepiece and looking down the tube at the back of the objective: bubbles appear as bright spots or rings. Wipe off the drop and apply a fresh one.

Too much oil, wrong cover glass, upside-down slide

  • A large pool of oil spreads to the stage and slide clips and eventually onto the condenser.
  • A cover glass thicker than the objective's correction (0.17 mm) adds spherical aberration that no amount of focusing can fix.
  • A slide placed cover-glass-down puts the full thickness of the slide between objective and specimen, so the 100x lens simply cannot reach focus.
  • Using the coarse focus knob at 100x risks pushing the lens through the cover glass.

Cleaning and caring for oil immersion lenses

Clean the 100x objective at the end of every session, not once a week. Dried oil becomes sticky and attracts dust.

  1. Lower the stage and remove the slide.
  2. Blot excess oil from the objective tip with clean lens paper, without rubbing.
  3. Wipe gently with a fresh piece of lens paper moistened with the cleaner your microscope's manufacturer recommends, using a spiral motion from the centre outwards.
  4. Finish with a dry piece of lens paper and check the surface with a magnifier or an inverted eyepiece.
  5. Remove oil from the slide with lens paper or a soft tissue before storing or discarding it.

Avoid strong solvents such as acetone on objectives, because they can attack the cement holding the lens elements. Never use ordinary paper towels or clothing on optical surfaces.

Oil immersion microscope function in practice: where it is used

Oil immersion is routine wherever structures sit near the limit of light optics. In microbiology it is standard for Gram-stained bacteria, where shape and arrangement of cells a micrometre or two long must be seen clearly. Clinical haematology relies on it for blood smear differentials and parasites. Veterinary laboratories use the same technique for blood films and cytology, which is why "oil immersion microscopy veterinary" is a common search.

In cell biology, high-NA oil objectives are the default for fluorescence and confocal imaging of fixed cells, because brightness and resolution both rise with NA. Specimen preparation still decides much of the result; the basics of making good slides are covered in the guide on how to prepare a microscope slide.

Conclusion: a repeatable routine beats a perfect lens

Oil immersion microscopy is simple once the order of steps becomes a habit: focus at low power, centre at 40x, add a single drop, bring in the 100x objective, use only the fine focus and clean everything afterwards. Matching the oil type to the job and keeping dry objectives away from oil protects both the image and the optics.

Frequently asked questions

Why is oil used with the 100x objective?

Oil has nearly the same refractive index as glass, so steep light rays from the specimen are not refracted away at a glass-to-air boundary. This lets the objective reach a numerical aperture above 1.0 and resolve finer detail.

Which objective lens uses oil immersion?

Usually the 100x objective, marked "Oil" or "HI" and often with a black ring. Some research microscopes also have 60x or 63x oil objectives.

What is the magnification of an oil immersion microscope?

With a 10x eyepiece and a 100x oil objective, total magnification is 1000x. The real benefit of oil is higher resolution, not just higher magnification.

Can you use the 40x objective after applying immersion oil?

No. The dry 40x lens sits too close to the slide and will dip into the oil. Clean the slide first or switch directly to the 10x objective.

Can you use mineral or cooking oil instead of immersion oil?

It is not recommended. Household oils do not have a controlled refractive index, can contain impurities and may leave residues that are hard to remove from the lens.

How do you clean immersion oil off a microscope lens?

Blot the oil with lens paper, then wipe gently with lens paper moistened with the cleaner recommended for your microscope, and finish with a dry sheet. Avoid acetone and paper towels.